Products
-
CT-3804: 4 channels Analog Input
CT-3804: 4 channels Analog Input, Thermocouple(J type, K type, E type, T type, Stype, R type, B type, N type)
Module features
◆ The module supports 4-channel thermocouple signal acquisition
◆ The module carries with 4 analog indicators
◆ The module supports 9 kinds of conventional thermocouple temperature measurement type
◆ The internal bus of the module and field input adopts magnetic isolation
◆ The module input channel supports TVS overvoltage protection
◆ 24-bit ADC resolution (Σ-δ type)
-
CT-3808: 8 channels Analog Input,Thermocouple
CT-3808: 8 channels Analog Input,Thermocouple( J type, K type, E type, T type, Stype, R type, B type, N type)
◆ The module supports 8-channel thermocouple signal acquisition
◆ The module carries 8 analog LED indicators
◆ The module supports 9 kinds of conventional thermocouple temperature measurement type
◆ The internal bus of the module and field input adopts magnetic isolation
◆ The module input channel supports TVS overvoltage protection
◆ 24-bit ADC resolution (Σ-δ type)
-
ODOT-PNM02 V2.0 / V2.1: Modbus-RTU/ASCll or Non-standard protocol to ProfiNet Converter
ODOT-PNM02 V2.1
Modbus (master/slave, RTU/ASCII) to ProfiNET, 2 port serial port (RS485/ RS232 / RS422), supports 50 slots, 200 commands in TIA portal (by configured software), support MAX 60 slaves
♦ Supports protocol conversion between Modbus and PROFINET
♦ Supports 2* RS485/RS232 or 1*RS422
♦ Supports Modbus master or slave, and supports RTU or ASCII
♦ Supports working temperature of -40〜85°C
♦ Supports data area: 2 serial Modbus-RTU/ASCII to PROFIBUS gateway with Max. input 1440 bytesand Max. output 1440 bytes
♦ Supports one key reset
♦ ODOT-PNM02 V2.0 supports Maximum slots: 50
♦ ODOT-PNM02 V2.1 supports 60 slaves (200 read and write commands)
-
CP-9131 the PLC controller
CP-9131 is the first version of ODOT Automation PLC, the programming environment follows the IEC61131-3 international standard programmable system, and it supports 5 programming languages such as Instruction List (IL), Ladder Diagram (LD), Structured Text (ST), Function Block Diagram (CFC/FBD) and Sequential Function Chart (SFC).
The PLC could support 32 pcs of IO modules, and its program storage supports 127Kbyte, data storage supports 52Kbyte, the data storage area contains input area of 1K(1024Byte), output area of 1K(1024Byte), and intermediate variable area of 50K.
With built-in standard serial communication RS485 interface, it carries with 2 RJ45 interfaces which is a small PLC with rich functions.
CP-9131 is the core component of the whole C series, its main work is not only responsible for executing the user’s logic program, but also responsible for all I/O data receiving and sending, communication data processing and other works. With rich instructions, reliable function, good adaptability, compact structure, easy to expand, cost-effective, strong versatility, programming, monitoring, debugging, field operation are very convenient, the PLC could be applied to a variety of automation systems.
The Ethernet interface on the CPU supports the Modbus TCP Server function, supports the third-party Modbus TCP Client to accesss data, supports Modbus TCP Client function, supports to access to data of third-party Modbus TCP Server.
The RS485 port supports the Modbus RTU master, Modbus RTU slave, and supports third-party devices to communicate with PLC through a serial port.
-
ODOT B64 series integrated I/O module-BOX-64
ODOT B series integrated I/O module consists of communication board (COMM board) module and extended IO module. The COMM board could select the corresponding bus module according to the communication interface of the controller system. The mainstream industrial communication protocols include Modbus, Profibus-DP, Profinet, EtherCAT, EtherNet/IP, CANopen, CC-Link, PowerLink, etc. The extended I/O module is divided into six categories: digital input module, digital output module, analog input module, analog output module, special module, and hybrid I/O module.
The COMM board and extended IO modules could be freely combined based on site requirements. The integrated IO module could lower the cost when there are few data points.
-
ODOT-MS100T/100G Series : 5/8/16 Port Unmanaged EtherNet Switch
MS100T
10/100 Mbps self-adaption,(Auto-MDI/MDI-X)
Supports IEEE 802.3 for 10BaseT
Supports IEEE 802.3u for 100BaseT and 100BaseFX
Supports IEEE 802.3xfor flow control
Supports broadcast storm protection
Supports working temperature: -40~85℃
5/8/16 ports unmanaged Ethernet Switches DIN-rail
-
CT-5321: Modbus Serial Port Module
CT-5321 Modbus Serial Port Module
1 Module Description
The Modbus serial port module supports 1 channel RS485/RS232 /RS422(optional), supports Modbus RTU/ASCII protocol, and supports master, slave and free transparent transmission mode.
The serial Module CT-5321 could be applied with the adapter modules, so it could convert Modbus into other protocols such as Modbus TCP, Profinet, EtherCAT, EtherNet/IP, etc. When the module is used, serial port parameters and Modbus instructions should be configured in IO Config software.
Devices with RS485/RS232/RS422 interface, which support modbus-RTU/ASCII, could be applied with CT-5321 to realize interconnection with upper PLC or upper computers. CT-5321 could be applied with devices such as: PLC, DCS, remote IO, VFD, motor start protection device, intelligent high and low voltage electrical apparatus, power measurement device, intelligent field measurement equipment and instruments, etc.
-
ODOT Remote I/O Module
Flexible protocol module and I/O module plug and play, features as below:
1. Designed with a max of 32 modules, each I/O module is built with 16 channels and each have LED indicator.
2. Supports an overall of 512 I/O points and self healing;
3. The I/O module back plate cable can be extended to 15 meters to be used in multiple panels;
4. WTP is from -40~85℃ with a warranty of 3 years;
5. High speed 12M back plate bus, with 32 digital quantity modules of a refreshing period at 2ms and analog quantity is 2ms;
6. Supports Modbus-RTU, Modbus-TCP, Profinet, Profibus – DP (DPV0), EtherCAT, Ethernet/IP and others up to 12 kinds of the main stream protocol.
-
CT-2224: 4 channel digital output/24VDC/ Source type
CT-2224: 4 channel digital output/24VDC/ Source type
◆the module supports 4-channel digital output, the output voltage is 24VDC and the output high level is valid.
◆the max output current of DO single channel is 3.3 A.
◆the module could drive field equipment (relay, solenoid valve, etc.)
◆the module internal bus and field output are isolated by optocoupler
◆the module carries with 4 digital output channel LED indicator
◆the module has the functions of thermal shutdown and overcurrent protection
◆the module supports short circuit protection and overload protection
-
AIO BOX-MT124F: Integrated IO Module MODBUS 16DI
MiniBOXIO
♦ AIOBOX-MT124F supports 16-channel DI, supports source and sink two-way Input, input voltage 24v/0v.
♦ LED indicators for 16 channel input & output.
♦ Two or three-wire digital sensor can be connected through input channel.
♦ 32-bit counter is supported by every input channel (frequency: <200Hz).
♦ Thermal shutoff and overcurrent protection.
♦ The bus inside the module and the field input are isolated by optical coupler.
-
AIOBOX-MT623F: Modbus TCP/RTU/ASCII 8DI+8DO
MiniBOXIO
♦ AIOBOX-MT623F supports 8-channel DI, supports source and sink two-way input, input voltage 24v/0v.
♦ LED indicators for 16 channel input & output.
♦ Two or three-wire digital sensor can be connected through input channel.
♦ 32-bit counter is supported by every input channel (frequency: <200Hz).
♦ Thermal shutoff and overcurrent protection.
♦ The bus inside the module and the field input are isolated by optical coupler.
-
CT-5711: Bus extended master module
CT-5711 Bus extended master module
Module Description
The bus extened master module is used to extend the bus.The bus extended master module has no process data and configuration parameters.